共搜索到33979条信息,每页显示10条信息,共3398页。用时:0小时0分0秒437毫秒
Trans. Nonferrous Met. Soc. China 24(2014) 279-284 Effects of Fe-Al intermetallic compounds on interfacial bonding of clad materials Qian WANG, Xue-song LENG, Tian-hao YANG, Jiu-chun YAN State Key... at the interface between solid Al and Fe and the effects of intermetallic compound layers on the interfacial bonding of clad materials were investigated. The results showed that the interface between......
]. Journal of Materials Processing Technology, 2003, 137(1/2/3): 10-16. [3] LEE J S, SON H T, OH I H . Fabrication and characterization of Ti-Cu clad materials by indirect extrusion [J]. Journal of Materials... pressing/extrusion process [J]. Computational Materials Science, 2008, 44(2): 247-252. [5] RHEE K Y, HAN W Y, PARK H J, KIM S S. Fabrication of aluminum/copper clad composite using hot hydrostatic......
......
Bonding properties of interface in Fe/Al clad tube prepared by explosive welding SUN Xian-jun, TAO Jie, GUO Xun-zhong College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China Received 26 October 2010; accepted 11 April 2011 Abstract: A Fe/Al clad tube was prepared by explosive welding. Then the bonding characteristic......
of flexible copper clad laminate(FCCL), i.e. base materials used for FPC. The FCCL generally consists of copper and polyimide(PI) layers, and thin and homogeneous structures with good interlayer bonding... Fabrication of two-layer flexible copper clad laminate by electroless-Cu plating on surface modified polyimide Soo-Min HWANG, Jun-Hyung LIM, Chang-Min LEE, Eui-Cheol PARK, Jun-Hyuk CHOI, Jinho......
Al 1060/Pure Iron Clad Materials by Vacuum Roll Bonding and Their SolderabilityQian Wang,Xuesong Leng,Jiuchun Yan,Weibing Guo,Yu Fu,Tianming LuanState Key Laboratory of Advanced Welding and Joining,School of Materials Science and Engineering,Harbin Institute of Technology摘 要:Al 1060/pure iron clad materials were produced by vacuum roll bonding.The......
J. Cent. South Univ. (2012) 19: 882-886 DOI: 10.1007/s11771-012-1087-1 Casting-cold extrusion of Al/Cu clad composite by copper tubes with different sketch sections LUO Jun-ting(骆俊廷)1, ZHAO Shuang... to the metallurgy bond of boundary interface between aluminum and copper. Key words: Al/Cu clad composite; casting-cold extrusion; sketch section; finite element simulation 1 Introduction Good......
conductivity still maintained. In this regards a drawn Cu/Al bar clad materials for electric wire have received much attention compared to Cu wire materials [3,7,8]. However, it is difficult to fabricate the Cu/Al bar clad materials because brittle intermetallic compounds are inevitably formed at the interface and brittle copper oxides are easily produced at the Cu surface during drawing and post heat......
Multilayer Clad Plate of Stainless Steel/Aluminum/Aluminum Alloy袁家伟,庞玉华School of Metallurgy Engineering, Xi’an University of Architecture & Technology摘 要:The 3, 5, 20 layer clad plate from austenitic stainless steel, pure aluminum and aluminum alloy sheets were fabricated in different ways. The stretch and interface properties were measured. The result......
. Synthesis of nanocrystalline materials-an overview [J]. Materials Science and Engineering A, 2001, 301: 44-53. [8] Huang B, Tokizane N, Ishihara K N, Shingu P H, Nasu S. Amorphization of Al-Fe alloys formed..., 2009, 57: 3529-3538. [12] Fadeeva V, Leonov A V. Formation of Al-Fe supersaturated solid solution by mechanical alloying [J]. Materials Science Forum, 1992, 90: 481-488. [13] Bayraktar E, Katundi D......